Classic Cars / GMC / Car for sale

1977 GMC Sierra 1500

Sale price: $1.00 make an offer

Car location: Hartselle, Alabama, United States

Sale type: Fixed price listing

Technical specifications, photos and description:

Got questions?
Ask here!

1977 GMC Sierra 1500 for sale

Current customer rating: current rating for this car(2.25) based on 45 votes
1977 GMC Sierra SWB 2WDPLEASE READ COMPLETELYLOTS OF PARTSLOTS OF DETAILSHere we go!!• This truck is set-up for an LS engine/Automatic transmission install. Or you can install a SBC/Trans.• Engine and Transmission NOT included.• This is a project truck.• The hard work has been Completed.• Clean Alabama title.* I have know this truck for over 20 years and the last two owners and to the best of our knowledge this truck has never been hit. Frame is straight and solid.• From the factory this was a V8, Auto, PS,PB,A/C truck• This truck was a LWB. I have shortened it and put a 81-87 SWB bed on it with driver's side fuel door.* New LH Tank's Inc. fuel tank for carburetor.• Truck is partially stripped to the metal. I did not spray primer on it so, that you could see how good the sheet metal is underneath. Nothing here is covered up.• All Rust repair and metalwork is Complete, welded and ground down:New Floor Patch Panels, L&RNew Interior Footwell Kick Panels, L&RNew Lower Exterior Cowl Panels, L&RFirewall AC holes filledBed stake holes have been filled and welded.• WHEEL TUBS This is a cool focal point of this truck!! New Auto Metal Direct 4” WIDER Rear Wheel Tubs installed in the bed. This will accommodate a 12”+ wide wheel. Please note the attention to detail of the bed floor ribs and radiuses around the new wheels tub to make it look factory. Quality workmanship. Welds are ground and ready for primer.This truck is ready for paint and bodywork to begin.• Stock 12 Bolt Rear end with 3.08 gearsNew pinion seal, fluid and gasket• Also included is a Ford 8.8 Rear end:Narrower than the 12 bolt to allow deeper dish and wider wheels59½” wheel mounting flange to wheel mounting flange3.73 gearsLimited SlipDisc brakes. Calipers and rotors not includedJasper Engines certified rebuiltAll factory brackets cut off and ground smooth. Ready for new brackets.• Quarter Window Frames have been dismantled, bead blasted and Powder Coated Semi-Glass Black.• All Original Glass for the truck is included. None scratched nor broken. Windshield was replace a few years back.• Drip rail moldings have been stripped. The channel and the backs have been Powder coated Semi-Gloss Black. The stainless trim looks very nice.• Two different factory gauge clusters go with the truck. One, the factory Gauge cluster that came with the truck, not the dummy light version. Also, I acquired a nice electric gauge cluster set out of 1991 Suburban. If you choose to go the LS route, use this set of gauges so that you can tie your speedometer and cruise control into the ECM.• Tail Light lenses were replaced recently, very nice.• I did a complete brake job on the truck about a year ago+ before tearing it down. I replaced the calipers, master cylinder, brake booster, rear wheel cylinders, turned the drums and rotors, bearings, seals, front and rear hoses and flushed the system with new DOT4 brake fluid.• The original truck harness is in a box.* Standard steering column• All parts that were removed from the truck are labeled, along with a labeled zip-lock bag of screws to go with the parts. All fasteners have been bagged and tagged.SUSPENSION• From the factory, this truck comes equipped with the 2WD HD Suspension1¼” rotors, heavier spindles, etc….• NEW in the Box, never opened: McGaughy's 4.5”/6” Deluxe Lowering Kit. #93150Dropped Front Spindles, 2” shorter Front Coil SpringsRear Flip Kit, Flip Plates, Flip Pads, C-Notch PlatesI have already installed the C-Notch Boxing Plates only.C-notched the frame, Bolted and Welded C-Notch Plates into place.This is the most difficult part of the Deluxe Lowering Kit• Front Sway Bar, I have scavenged the salvage yards and obtained a one ton truck 1¼” front sway bar and factory brackets. No modifications needed, holes are already drilled, bolts right in.• New in the box, Energy Suspension 1¼” Sway Bar Bushing Kit.• New in the box, Energy Suspension Control Arm Bushing Kit• New in the box, Energy Suspension Cab Mount Bushing KitLS Conversion Parts• New in the Box, TeJas Steelworks Squarebody LS Conversion KitLS Motor Mount AdaptersHigh Clearance Transmission CrossmemberRadiator Fan Shroud for dual SPAL FansGEN 3 LS ECM Mounting BracketGEN 3 Drive by Wire, Pedal Mounting BracketTeJas LS Swap GuideI have test fit a LS engine/transmission into chassis with all bracket to ensure fit and clearance. Passenger's frame rail has been notched for the A/C compressor hoses.• Radiator, NEW in the Box, never installed, 454 Big Block Radiator, Copper and Brass for a 1980 ½ ton C-10, no cheap plastic and aluminum radiator here.New LMC Top Radiator Mount Panel and Rubber PadsNew top AC Delco brand radiator hoses for the LS conversion.TeJas Radiator Fan Shroud for dual SPAL Fans. Fans not included.Air Conditioner• The truck is a factory AC truck. I have saved all ductwork, vents, heater/evaporate box and dash components.• NEW in the Box, Vintage Air #754175, 1973-80 Chevrolet Pickup w/ Factory Air SureFit™ Evaporator Kit.GEN IV 4-Vent Evaporator KitSureFit Control PanelAccessory KitCompressor, Condenser, Belts, Pulleys not included.I have filled in, welded up and ground down all of the factory A/C firewall hole, among other holes.I have trial fit and mounted the Vintage Air Evaporator to the truck and drilled all of the new necessary holes for the new Vintage Air Unit heater and AC hoses.More NEW in the Box Parts• RH Battery Tray and Support• Tanks Brand, LS Fuel Injection Tank Kit #TM11B-T-KITFuel Injection Style TankFuel Injection In-Tank Fuel PumpSending UnitTank StrapsTank support bracesFuel neck, filler hose, vent hose, cap and housing.• AC Delco Door Lock Cylinder Kit• Front Fender Hardware Kit• GM Style Reproduction Stainless Exterior Door Mirrors• Fit to doors, Holes drilled, Nutserts installed. Ready to bolt on.• Classic Industries Instrument Cluster Bezel - Black• Classic Industries Interior Door Panels – Maroon• Classic Industries Padded Dash – Maroon• Driver's side 3-point seat belt harness – Maroon• RH Interior Kick Panel – Black• LH Interior Kick Panel – Black• LH Kick Panel Vent Cover – BlackA notebook will be provided with most all receipts, instruction manuals, directions of products, etc that I have.If you are building a super nice truck, you might consider new front fenders and hood.NO Tire kickers Please!! I Don't have the time.No, I don't need help selling the truck. Not interested in trading either.This truck is listed locally and other websites. I reserve the right to end auction at anytime.I do have a 6.0L engine and 4L80E transmission, harness, pedal and other related parts at an additional cost.For additional photos, information, questions please feel free to call or text me at (Two,five,six) 566-OO99.

Also published at eBay.com

Want to buy this car?

Comments and questions to the seller:

Name E-mail
Text
Antispam code: (enter the number)

Other classic GMC cars offered via internet auctions:

Latest arrivals: